Garage door sensors are safety devices that prevent the door from closing on people, pets or objects in the doorway. Garage door sensors are quite valuable tools as they can keep your child or pet safe. The bad news is that they may become faulty or even break sometimes. If the garage door sensor is not aligned properly, it can result in serious injury, or even death. This article helps you align the faulty garage door sensor and ensure safety.
Garage door sensors are located above the floor at each side of the door opening and generate a low-voltage beam that completes the electrical circuit when the door is activated. Garage doors may display a variety of symptoms when the sensors need attention. In most cases you can troubleshoot the system and correct the cause of problems. If you are not sure of the process call professional garage door repairs Brooklyn NY company for help.
1. Clean the dust from electric-eye lenses on each sensor. Open and close the garage door repeatedly using the control on the garage wall or the remote unit from a vehicle. If the door does not close completely without hesitation, proceed with adjusting the sensors.
2. Loosen the small nuts that hold each sensor to the L-brackets, just enough so that the sensors remain facing each other and can be moved by hand.
3. Adjust each sensor in small increment by hand until the green or red power-indicator lights on each are illuminated. This indicates the electric eyes are aligned and the circuit is complete. Tighten the nuts on each sensor.
4. Open and close the garage door repeatedly using the control on the garage wall or the remote unit from a vehicle. If the door does not close completely without hesitation, proceed to troubleshoot the electrical circuit.
5. If adjusting the sensors does not work out, then the next step is to go check out the electrical circuit. For this, unplug the power cord from the outlet and identify the connection terminals where the ends of the low-voltage senor wires attach. Reattach a loose wire to the appropriate terminal. Plug in the power cord and observe the lights on the sensors. If both lights are not illuminated, proceed to the next step.
6. Inspect the double-strand insulated low-voltage wires from each sensor to the back of the garage door opener. If any you notice any damages, you should set right any bare, burned or broken wires in one or more places.
7. If no damage is noted, one or both sensors must be replaced. For replacing garage door sensors call professional garage door repairs NY company to carry out the job for you.
1. United Overhead Door Corp: United Overhead Door Corp has over 50 years of experience in manufacturing, installation, repair of garage door in New York. All of the technicians are factory trained. If you need any garage door repair services call at 800-874-3667, fax at 914-964-0964 or you can send emails at info@uniteddoor.com. Office is located at 21 Saw Mill River Road, Yonkers, N.Y. 10701. For more information, visit: http://uniteddoor.com.
Garage door sensors are located above the floor at each side of the door opening and generate a low-voltage beam that completes the electrical circuit when the door is activated. Garage doors may display a variety of symptoms when the sensors need attention. In most cases you can troubleshoot the system and correct the cause of problems. If you are not sure of the process call professional garage door repairs Brooklyn NY company for help.
Garage door sensors repair steps
Before you begin, make sure the electrical cord from the opener is plugged in and the electrical circuit is active.1. Clean the dust from electric-eye lenses on each sensor. Open and close the garage door repeatedly using the control on the garage wall or the remote unit from a vehicle. If the door does not close completely without hesitation, proceed with adjusting the sensors.
2. Loosen the small nuts that hold each sensor to the L-brackets, just enough so that the sensors remain facing each other and can be moved by hand.
3. Adjust each sensor in small increment by hand until the green or red power-indicator lights on each are illuminated. This indicates the electric eyes are aligned and the circuit is complete. Tighten the nuts on each sensor.
4. Open and close the garage door repeatedly using the control on the garage wall or the remote unit from a vehicle. If the door does not close completely without hesitation, proceed to troubleshoot the electrical circuit.
5. If adjusting the sensors does not work out, then the next step is to go check out the electrical circuit. For this, unplug the power cord from the outlet and identify the connection terminals where the ends of the low-voltage senor wires attach. Reattach a loose wire to the appropriate terminal. Plug in the power cord and observe the lights on the sensors. If both lights are not illuminated, proceed to the next step.
6. Inspect the double-strand insulated low-voltage wires from each sensor to the back of the garage door opener. If any you notice any damages, you should set right any bare, burned or broken wires in one or more places.
7. If no damage is noted, one or both sensors must be replaced. For replacing garage door sensors call professional garage door repairs NY company to carry out the job for you.
Garage door repair services in NY
Garage door repair New York company, United Overhead Door Corp1 located at Yonkers, NY has been a trusted and reputable company serving local residents of Yonkers. The company offers both commercial garage door repair and residential garage door repair services, and it can provide fast service for urgent needs. United Overhead Door Corp is the right company to trust you are dealing with a broken garage door. To have the best value for money and dedicated repair solutions, it is important to choose an experienced garage door technician in a cost-effective manner.1. United Overhead Door Corp: United Overhead Door Corp has over 50 years of experience in manufacturing, installation, repair of garage door in New York. All of the technicians are factory trained. If you need any garage door repair services call at 800-874-3667, fax at 914-964-0964 or you can send emails at info@uniteddoor.com. Office is located at 21 Saw Mill River Road, Yonkers, N.Y. 10701. For more information, visit: http://uniteddoor.com.
No comments:
Post a Comment